Slim subwoofer underseat with amp Active Powered Car- 600 Watts Max Power, Low Profile, 8 Inch Subwoofer, Remote Subwoofer Control, Built in Amplifier, for Truck, Boxes and Enclosures

Price: $78.00
(as of Feb 18, 2024 11:57:41 UTC – Details)

Product Description

Panel controls and features

A.POWER STATUS LED

This bio-color LED glows green when power ison and no problems are present. If one of theprotection circuit comes on, it will change to red.

B.PHASE SHIFT

Use this switch to help compensate for timealignment problems in the system. Suchproblems usually result from having thesubwoofer at a different distance from thelistener than the other speakers in the system.

C.AUTO POWER ON

The AUTO POWER ON(ON/OFF) is for highlevel(speaker-level) connections. When the switch is in the “ON” position, the subwoofer AUTO POWER ON when there is signal input[f the amplifier detected no signal input, the amplifier will auto turn off. If you prefer to usethe remote turn on/off onnection the switch is in the OFF position.

(Note: Please connect the remote terminalto the remote output of head unit as Fig.4. When you hear the unit turn ON/OFFPOP noise from the subwoofer.)

D.LOW PASS FILTER

This control permits you adjust the frequencyrange you want the subwoofer amplifier to receive. The subwoofer will reproduce all sound BELOW the frequency you set.

(Note: The low pass filter frequency can behigher or lower than the standard. Therehave +/-20% tolerance.)

E.BASS BOOST

The BASS BOOST feature will increase the

sound level in the bass frequencies.

F.INPUT GAIN CONTROL

After you have installed your system, turn thiscontrol to minimum.

Turn the head unit on (and the subwoofer willturn on via the remote connection). Turn thehead unit volume to about 2/3 full level.

Slowly turn up the subwooferinput gain controluntil you hear a small amount of distrotion.Then reduce the level until the distortion is

completely gone. Level the control at this setting

G.REMOTE LEVEL CONTROL

Attach the included remote level control to control the volume level of the subwooferindependently.

H.HIGH LEVEL(speaker low)INPUTSIf your head unit does not have RCA outputsyou can use the speaker outputs for the audiosource for the subwoofer. Use the suppliedcable and wire harness and connect theoutputs properly as shown in the connectiondiagram in this manual

I.LOW LEVEL RCA INPUTS

Low level inputs are the recommended way to introduce the audio signal to the subwooferif RCA outputs are present on your head unit or other signal source (such as a sound processor).

J.FuSE

Do not use a fuse with a different valueand NEVER replace the fuse with a wireor coin.

K.POWER INPUT TERMINAL

Low LevelInput Wiring

Low-level (RCA) input wiring is preferred for best audio performance. Most trunkor hatchback installations will require a 15-20 feet RCA cable, while pick up trucksand under-seat installations will require a 6-12 feet RCA cable. Always use ahigh quality cable.

NOTE:Do not connect BOTH the high level and low level inputs fromyour receiver to your amplifier at the same time

High Level Input Wiring

The high level input(s) should only be used when your receiver lacks RCA outputs.If the RCA outputs are not present, connect the speaker outputs from the receiverto the high level input connector of the amplifier, Be sure to observe polarity toavoid audio phase problems.

NOTE:Do not connect BOTH the high level and low level inputs fromyour receiver to your amplifier at the same time

Power Connections

Connect the ground terminal to the closest point on the chassis of the vehicle. Keepthis ground wire to less than 39″ (100 cm) in length. Use 8 gauge(or heavier) wire.

Connect the remote terminal to the remote output of head unit using 16 gauge ( orheavier ) wire.

Connect an empty fuse holder within 18″ (45 cm) of the car battery, and run 8 gauge(or heavier) cable from this fuse to the amplifier location. Then connect the fuseholder to the “BATT+”(+12V) connection on the subwoofer rear panel.

Standard technical specifications

RMS power 150W THD ＜0.4% Signal-to-noise ratio >90dB Frequency response 20Hz-150Hz High level input sensitivity 1.0~9.0V Low level input sensitivity 0.1~6V Low Pass Filter 50Hz-150Hz Bass Boost 0to+18dB Subsonic Filter 20Hz Fuse rating 15A/25A Subwoofer 8″ Dimensions(L x Wx H) 11.4×8.46×2.56in\290x215x65mm

Built-in Amplifier – A built-in 600 Max watt amplifier powers the subwoofer
Pulse Width Modulated – This design controls the output voltage and current precisely by not only removing the output current sensing loss, but also eliminating all secondary feedback circuitry. It increases efficiency, is lighter, smaller reliable
Variable Low-Pass Filter – A low-pass filter is an electronic circuit that removes all the notes below the filter’s frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s)
High Level Input – Speaker level inputs are commonly referred to as high-level inputs. It will be used to connect the PH-80 to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs